- Crusher Machine
- Grinder Mill Machine
- Dryer Machine
- Rotary Dryer
- Three Drum Dryer
- Bean Dregs Dryer
- Poultry Manure Rotary Dryer
- Wooden Sawdust Dryer
- Sand Dryer Machine
- Waste Food Scrap Dryer
- Fly Ash Dryer
- Quartz Sand Dryer
- Brewers Grain Dryer
- Mineral Slag Dryer
- Coal Slime Dryer
- Graphite Rotary Dryer
- Sludge Dryer
- Steel Slag Dryer
- Fertilizer Drying Machine
- Fruit Residues Dryer
- Cassava Dregs Dryer
- Petrol Coke Dryer
- Cow Dung Dryer
- Air Current Dryer
- Bentonite Dryer
- Dry Mortar Dryer
- Rice Husk Dryer
- Oil Palm Fibre Dryer
- Desulfurization Gypsum Dryer
- Kiln Machine
- Ore Benefication Machine
Lime rotary kiln is the key equipment for the calcination of limestone, dolomite, bauxite, clinker, etc. We can also make design for your reference according to your capacity requirment and heating fuel for the lime rotary kiln.
Lime rotary kiln is mainly composed of kiln shell, refractory bricks, supporting device, supporting device with catch wheel, transmission device, lubrication device, mobile kiln head and sealing device at the end of the kiln.
1. Supporting device: advanced shaft structure, automatic temperature measuring device and electrical heating.
2. Catch wheel: including two kinds mechanical wheel and hydraulic pressure.
3. Gears: single or double. Control the rotating speed by buncher, DE machine and frequency variable motor. Be reliable, energy-saving, and efficient.
4. Kiln shell tire bolster: lower bolster has three types: fixed, zoom and floating. The structure is simple, replacement is convenient and won’t hurt cylinder.
5. Sealing equipment: there are many kinds for choice according to kiln models, including air cylinder edge sealing, spring edge sealing, and graphite block sealing and combination for above. The sealing effect is very good.
6. Kiln head hood: including stationary type and flexible type.
2. Rotary Kiln belongs to open type calcining, the structure of kiln body is simple, airflow is unblock, the gas containing S could be exhausted in time meanwhile the S during burning is hard to adhering so the sulphur content of products is low which could meet the steel-making requirements. At the same time material will go ahead evenly inside kiln with even heating, so the quality of production is stable and crude burning rate and over-burning rate is very low thus it could calcine high activity lime for steel-making. Under the same condition, lime activity produced by rotary kiln which could be 340-380ml or even 400ml is over 30ml higher on average than that manufactured by gas kiln.
3. Rotary Kiln could directly calcine 10-50mm fine power level limestone, normally 0-30mm fine power level limestone accounting for 30-40% of total volume which couldn’t be used for other type kiln. Complying with the fineness of steel raw material, sintering gradually takes use crude lime instead of limestone, as fine limestone couldn’t be used comprehensively. Rotary kiln production line could not only use good limestone ore resources, but also meets the lime industry sustainable development policies.
4. Utilizing vertical preheater in kiln end could adequately use high temperature smoke created by calcining inside of kiln which could initially pre-break down from normal temperature preheating. This could not only largely increase output of rotary kiln, but also fully decrease heat consumption each unit product.
5. Utilizing vertical cooler in kiln head could not only cool quickly of high temperature lime and increase activity, but also it is convenient for conveying and saving. Meanwhile it could gain high temperature 2nd wind when entering into kiln, which could efficiently increase temperature inside of kiln, decrease burning consumption.
6. The temperature of smoke discharged from vertical preheater of kiln end is low, normally it is between 280-350℃, whose dust containing is about 20g/Nm3, that is really low, this could make simple and efficient follow-up smoke treatment meanwhile the gas after treated could meet the environment protection standard.
7. The most important advantage of lime produced by rotary kiln is stable. Seen from total development trend, our active lime production equipment should focus on local market. Not only for adaptability of manufacturing capacity, but also for adequately utilizing good limestone ore resources, rotary kiln both have better developing future.
|Rotary kiln (m)||2.8×55||2.8x43||3x50||3.2x50||3.3x55||3.6x55||3.8x55||4x60||4.3x60|
|Calcination temp. (°C)||1300||1300||1300||1350||1350||1350||1350||1350||1350|
|Fuel (coal)||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder||Gas/ Powder|
|Fuel consumption (kJ/kg)||6670||5500||5400||5400||5400||5300||5250||5200||5000|
|Cooling equipment||Vertical cooling||Vertical cooling||Vertical cooling||Vertical cooling||Vertical cooling||Vertical cooling||Vertical cooling||Vertical cooling|
Please Feel free to give your inquiry in the form below.We will reply you in 24 hours.